BAKBAKFlip G2 Hard Folding Truck Bed Tonneau Cover | 226307 | Fits 2004 - 2014 Ford F-150 6' 7" Bed (78.8")

Simple instructions easy to follow. I had to trim both rails approximately 1/2” due to having a drop in bed liner. Not a big deal but it had to be done in order for the tail gate to close. These are the best bed covers on the market. Worth the extra money.

I previously had a L**d tonneau, soft roll up, held down by velcro strips down the sides. I spent about $300-$400 for it. After the first year, and some shrinkage, it never really fit right. This one fits perfect. I love the multi points of cable release as you unfold the tonneau. Also, I no longer am required to stand at the back of the bed of the truck to pull on cables on both sides of the roll up tonneau to release the latches. I can stand on one side or the other of the tonneau and it releases both sides. Fold up is easy, however, with each fold you are not lifting more weight than the previous fold. By the time you are lifting the last fold it is a little awkward. I love the matte finish and looks very sleek overall on the bed of the truck. Much better than the roll up that sat about an inch above the level of the bed of the truck. Set up was ok, I took my time over about 90 minutes, distractions in-between, but if I had focused I am guessing I could have set the entire thing up in 20-30 minutes. There were a couple spots on instructions where they were not clear, however, the pics helped. One thing I wish they had provided were plugs to place in the holes at the front of the tonneau. I know they provide the tubes to help drain, however, my truck has a spray in bed liner, sealing the spots where you can pop out the plastic bed plugs and run your drain tube out. They recommend drilling a hole to place the end of the tube, but I would prefer to plug the holes of the tonneau and just let the rain or snow drain off on its own. I wasn't sure about the rubber seal around the edges as there were a couple points in which there were waives or bumps and it did not look like it was going to seal properly. They recommend getting out a blow dryer to heat up the rubber seal and it would eventually lay flat. They also recommended you could let is sit in the heat of the sun. I decided to do the latter. Within a few hours the rubber seal laid flat and smooth against the truck bed. Overall, I am very pleased with the product. Is it worth over $1000 you pay, that is up to you to decide. I don't believe it is. When I compare to others, roll up or hard flip tonneau, considering the latches and other aspects, I think it is more like a $650-$800 product, but no where near $1000.

The process of installing was very quick and easy. I watched a YouTube video and it walked through every step. Have had it on for about 3 months now and it has been great.

Super easy to install and looks amazing. Title and description could be better. It says for older F150 with 5' 6" bed, but listing shows photos of newer model F150 and only allows 5' 7" as smallest option. Listing could also mention about bull ring (stake pockets) fitment. Photos show that this cover works perfect with bull rings. Very happy with purchase.

The cover came in and the box was sitting up ok one end. The cover itself was fine. The two plastic corner pieces were broken. I emailed BAK and installed the cover. They quickly responded and asked for my address. Two days later, I had new end pieces but for a different model cover. Emailed them again, they expressed shipped the correct ends. Installed new corner pieces and cover is doing fine. One person can install it, 2 just speeds it up on holding and tightening. It lines up pretty easy and is not hard to put on. I added some foam weather stripping to the tailgate area, of my truck, to help move water away from going in the bed. So far, that has helped the cover be 99.5% water proof. Very little water gets into the bed now. I would trust my luggage in the back, even while driving, during a storm. The cover locks in place but is easy to unlock and fold up. I only loose about 6" of bed space with the cover folded up to the cab. This could be handy on day, with having the short bed on a crew cab F150. The only issue I have seen with the cover is the plastic end pieces. They do feel flimsy. I shouldn't be doing anything to mess them up but you never know. The BAK customer service was on top of my issue from shipping tho. I would recommend trying this cover is you are looking for one that can fold up to the cab, for maximum bed space without removing. The cover can be removed easily tho. Two screw down knobs, on the inside of the cover, is all you have to take off to remove from the truck.

I have wanted a hard folding bed cover for several years now. I did a lot of research and finally decided on the BAKFlip MX4 mainly because I can flip it against the cab. I have a tool chest mounted in my truck and I have enough room to open the lid about 2/3 of the way with the cover folded against the cab.What I like: Looks good and gives me some additional peace of mind knowing the bed is covered. The latching seems to be secure, and the bed stays dry (can't say 100% but I don't see obvious water streams when I open my tailgate after the rain). As I mentioned earlier, to me the biggest selling point was the ability to keep my tool chest in my truck bed since it can fold against the cab if needed. I have had soft rolling covers in the past with velcro seals and I would not ever use that kind again because I couldn't get it to stay sealed going down the highway. As far as packaging, the cover was packaged well and did not have any damage after shipping which I have read is a common issue with many hard folding covers. Assembly is also pretty easy.The bad: So this is a bit nit-picky but the cover and its packaging was covered in aluminum drill chips and shavings. I mean filled to the point where I had to use a leaf blower to clean it off before I handled it. I also had to deburr and clean the through holes where the 2 latches mount to secure the cover when opened. This doesn't really take away from the cover once installed, but the factory should take the time to clean off machining chips before sending out. This is the reason I did not give the cover 5 starts.

Needed to do some trimming on the box liner but the fit is perfect! Very well made.

parfaitement ajusté, très beau, facile a installé, très bon état malgré boite brise avec chariot élévateur !

Great truck box cover, the fit is awesome!

Top quality, easy to install, makes me feel like top ramen

Good product